Shindaiwa AH230 Operator's Manual

Browse online or download Operator's Manual for Power hedge trimmers Shindaiwa AH230. Shindaiwa AH230 Operator`s manual User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 20
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
SHINDAIWA OWNER’S/OPERATOR’S MANUAL
AH230 ARTICULATED
HEDGE TRIMMER
WARNING!
Minimize the risk of injury to yourself and others!
Read this manual and familiarize yourself with the contents.
Always wear eye and hearing protection when operating this unit.
This machine is designed for trimming hedge.
Do not use this machine for other purposes.
Do not operate or service this machine unless you clearly
understand this manual.
Keep this manual available at all times so that it may be referred
to if questions arise regarding this unit’s use.
Part Number 62849-94310
Rev. 12/04
Page view 0
1 2 3 4 5 6 ... 19 20

Summary of Contents

Page 1 - HEDGE TRIMMER

SHINDAIWA OWNER’S/OPERATOR’S MANUALAH230 ARTICULATED HEDGE TRIMMERWARNING!Minimize the risk of injury to yourself and others!Read this manual and fami

Page 2 - Contents

10251021WARNING!The cutting blades may move (oscil-late) when the engine is started. Keep away from the cutter assembly while starting the engine.Prim

Page 3 - Warning Labels

11Adjusting The CarburetorWARNING!The cutter attachment must never oscillate at engine idle speed. If the idle speed cannot be adjusted by the procedu

Page 4 - Operating Precautions

12Using The Hedge TrimmerCutting close to ground from a standing position, e.g. low shrubs. See below.Overhead CutHold the shaft upright with a 90O bl

Page 5

13General MaintenanceWARNING!Before performing any maintenance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are

Page 6 - Product Description

14Every 10 to 15 hours of operation:Remove and clean the spark plug.Adjust the spark plug electrode gap to 0.6 ~ .07 mm. If the plug must be replace

Page 7 - Powerhead Installation

15Cutter Blade AdjustmentWARNING!The cutter blades are very sharp! Always wear gloves when working around the cutter assembly.CAUTION!Operating the tr

Page 8 - Adjusting the Throttle Cable

16

Page 9 - Gearcase rotated to the

17Low Power OutputTroubleshooting Guide (Continued)

Page 10 - Ignition Switch

18

Page 11 - Stopping the Engine

19Declaration of Conformity

Page 12 - Attaching The

2Introduction The Shindaiwa AH230 Articulatied Hedge Trimmer is designed and built to deliver superior performance and reliability without compromise

Page 13 - 10-Hour Maintenance

Shindaiwa Inc.11975 SW Herman Rd.Tualatin, Oregon 97062 U.S.A.Telephone: 503 692-3070Fax: 503 692-6696www.shindaiwa.comShindaiwa Kogyo Co.,

Page 14 - 50-hour Maintenance

3Safety PrecautionsAn articulated hedge trimmer has the potential to do serious damage if misused, abused or mishandled. To reduce the risk of injury,

Page 15 - Long Term Storage

4IMPORTANT!Safety and Operation Information Labels: Make sure all information labels are undamaged and readable. Immediately replace damaged o

Page 16 - Troubleshooting Guide

5WARNING! Never transport the articulated hedge trimmer nor set it down with the engine running. An engine that’s running could be accidently accele

Page 17 - Low Power Output

6Technical SpecificationsUsing figure above as a guide, familiarize yourself with the Shindaiwa AH230 articulated hedge trimmer and its various componen

Page 18 - Additional Problems

71. Place the powerhead on a clean, flat surface, spark plug facing up.CAUTION!Do not remove the D-shaped shim washer! The D-shaped shim washer preve

Page 19 - Declaration of Conformity

8Adjusting the Throttle Cable1. Loosen the two 10 mm throttle cable nuts at the fan cover as shown below.Cable Adjuster Nuts2. Adjust the throttle cab

Page 20

9Adjusting the Hedge Trim-mer Cutter Assembly for Desired Cutting AnglesWARNING!Do not touch the cutter blades when the engine is running. The blades

Comments to this Manuals

No comments