C3410SHINDAIWA OWNER’S/OPERATOR’S MANUALC3410 BRUSHCUTTERWARNING!Minimize the risk of injury to yourself and others! Read this manual and familiarize
1010 IMPORTANT!Mix only enough fuel for your immediate needs! If fuel must be stored longer than 30 days and oil with fuel stabilizer is not used, i
1111 Starting the Engine (continued) WARNING!Never start the engine from the oper-ating position. WARNING!The cutting attachment may rotate when the
1212NEVER operate the unit with the cut-ting attachment shield or other protective devices removed! WARNING!A cutting attachment shield or other prot
1313 WARNING!n Before working with a blade-equipped unit, always inspect and clean the area of objects that could interfere with or damage the blad
1414IMPORTANT! MAINTENANCE, REPLACEMENT OR RE-PAIR OF EMISSION CONTROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL;
151550-hour MaintenanceEvery 50 hours of operation (more fre-quently in dusty or dirty conditions):n Remove and clean the cylinder cover and clean gr
1616341033139/150-Hour MaintenanceValve Adjustment1. Remove cylinder cover, rocker arm cover, and set piston at TDC-compresion. 2. Loosen adjuster l
1717Long Term Storagen Remove the spark plug and pour about 1/4 ounce of 2-cycle mixing oil into the cylinder through the spark plug hole. Slowly pul
1818Troubleshooting Guide ENGINE DOES NOT START%PFTUIFFOHJOFDSBOL 'BVMUZSFDPJMTUBSUFS'MVJEJOUIFDSBOLDBTF*OUFSOBMEBNBHF$POTVMU
1919Troubleshooting Guide (continued)ADDITIONAL PROBLEMS1PPSBDDFMFSBUJPO$MPHHFEBJSmMUFS$MPHHFEGVFMmMUFS-FBOGVFMBJSNJYUVSF*EMFTQFFETFUUP
22Throughout this manual are special “attention statements”.IMPORTANT!The operational procedures described in this manual are intended to help you ge
20SHINDAIWA LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010ECHO, INC'S RESPONSIBILITYECHO Incorporated’s (ECHO
21PURCHASED REPAIR PARTS AND ACCESSORIES• 90-day all applicationsATTENTION ENGINE POWERED PRODUCT OWNERSThis Shindaiwa engine powered product is a qu
22 ECHO INCORPORATED EMISSION CONTROL WARRANTY STATEMENTFOR ECHO AND SHINDAIWA BRANDSThe Environmental Protection Agency (EPA) and the California Air
23NOTES
ECHO Incorporated.400 Oakwood RoadLake Zurich, IL 60047-1564 U.S.A.Telephone: 1-877-986-7783Fax: 1-847-540-8416www.shindaiwa.com Yamabiko Corporation
33 WARNING! Use Good JudgmentALWAYS wear eye protection to shield against thrown objects.NEVER run the engine when transporting the unit.NEVER r
44Safety LabelsFigure 3IMPORTANT!Safety and Operation Information Labels: Make sure all informa-tion labels are undamaged and readable. Immediately re
55Brushcutter BladeCutting Attachment ShieldGear CaseThrottle TriggerProduct DescriptionUsing the accompanying illustrations as a guide, familiarize y
66Figure 9Cutting Attachment ShieldInstall the Cutting Attachment Shield C3410.1. Insert the cutting attachment shield between the outer tube and the
773/16-1/4 inch (4-6 mm) Throttle Free PlayAdjust Throttle Lever Free Play1. Remove the air cleaner cover by loosen-ing the two thumbscrews. See Figur
88Installing a Trimmer HeadNOTE: The C3410 is shipped with Holder A, the blade retainer (safety clip), Holder B, shaft bolt, and bolt guard installed.
99Turn the C3410 upside down so the gear case output shaft is facing UP and remove the shaft bolt, bolt guard and holder B from the gear case shaft.1
Comments to this Manuals