Shindaiwa DGW310DMC User Manual

Caution Do not operate the generator/ welder, or any other appliance, before you have read and understand the instructions for use and keep near for

8 DGW310MC DGW310DMC Breaker Starter Switch Output Change SW Slow Down SW Display Change SW Display Frequency

9 DGW310MC DGW310MC DGW310DMC Air Cleaner Sub tank Oil gauge Oil inlet Water drain plug Fuel lever /Straine

10 5-1. Eco Welding The equipment is incorporated in Eco Welding Feature that is aiming at performing The low noise, the lower fuel cons

11 Danger: Injuries ●Close all the doors and place lock during operation, to avoid injuries by unintentional touch of cooling fan

12 Caution: Burns ●Do not touch the engine and muffler during operation and immediately after stopping it, for the temperature can reach extremely

13 2 Insert the extension cord plug into The receptacle. In case of DGW310DMC, insert either A or B to be remote controlled. 3 Insert the plu

14 (1) Grounding A qualified electrician should perform the grounding work for the following 3 points. (Ground Resistance less than 500Ω) ●The ELCB g

15 (3) The ELCB has activated Caution: Electric Shock/Injuries ●Be sure to disconnect all the loads to the equipment when turning the b

16 △ Caution: Fire/Burns/Injuries ● When checking engine, always stop the engine and keep away from hire. Wait until the engine cools do

17 6-2. Coolant and Water Danger: Injuries ● Close all doors and locks during operating equipment to avoid injuries by accidental touch cooling

18 ● Mixture ratio of the coolant should be 30%-45% depending on the ambient temperature. ● Replace LLC at every year or 2000 hours. Recommended LLC

19 6-5 Battery Caution: Injuries to eye and skin ● Battery Fluid contains diluted sulfuric acid. Avoid contact with eyes, skin or cloth

20 Danger: Suffocation from exhaust fume ●Exhaust fume from engine contains many elements harmful to human. Do not operate this eq

21 7. Keep the engine idle for about 5 minutes. Restarting after stopping due to fue

22 7-2 Stopping 1. Turn the breaker to OFF . 2 .Turn the slow-down switch to ON . 3. Keep the engine (cool down) for about 5 minutes. 4. Turn the sta

23 8-2. Polarity There are 2 welding output terminals + and-. Select the polarity according to the operation, referring to the table below. Caution

24 8-4. Welding  Caution: Suffocation from welding fume ● Be sure to wear a welding mask in operation, because welding fume contains pois

25 Welding Current at the dial position (A) Position Freq MIN 1 2 3 4 5 MAX ECO 30 45 70 95 120 145 160 50Hz 70 90 135 175 215 260 280

26 9-1. Output Range (1) 3-P 200/220V (3-P 4-Wires)

27 9-2. Output Limitation Please refer to the table below, because electric tools and home appliances cannot be judged only by the rated. The rated

1 Introduction Thank you for purchasing Shindaiwa Sound Proof Diesel Engine Generator. ●T his user manual was prepared to ensure the safe operation

28 9-3. Operation Danger: Electric Shock ●Before connection or disconnecting a load cable from the receptacle, always turn the circuit breakers (3-

29 Caution ●The AC volt meter reads 3-P 200/200V apart from the circuit breakers position at ON or OFF when the engine driving. After the engin

30 The circuit breakers react on the AC power supply circuit only. In the simultaneous use of welding and generating, there may be

31 Danger: Electric Shock/Injuries ●Before checking, stop the engine and remove the engine key which to be kept by the person to do. ●Do no

32 Check Time Startup Every Every Every Every Every Check Items At 50 hrs 100 hrs 200 hrs 400 hrs 1000 hrs 2000 hrs 1 Check a

33 Check Time Every Every Every Every Every Check Items Startup At 50 hrs 100 hrs 200 hrs 400 hrs 1000 hrs 2000 hrs Clean Radiator Fin

34 2) Change Oil Filter 1st At 50 hrs 2nd or after Every 200 hrs 1 Drain the oil as described in (1)Change Engine

35 Caution ●Clean more frequently when it is used in dusty environment. ●Air Element Part No.: 1G347-11181 (Kubota) (4) Clean/Change Fuel Strainer

36 (6) Change Coolant/Water Change At 2000 hrs or 2 yrs Total capacity: 3L (including Sub Tank: 0.6L 1 Open the top do

37 If the equipment will not be used for more than 2 months, perform the following maintenance and storage procedure. 1 Remove the battery. (Refer t

2 Danger: Suffocation from exhaust fume

38 Symptoms Presumable Causes Actions 1. Insufficient Oil 1. Replenish Oil 2. High Water Temperature, 2. Keep the rated Insufficient Coolant/Wa

39 Warranty Sheet Type-B

2006.10 MEMO Shindaiwa Corporation Hiroshima Japan

3 Caution: Injuries to eye and skin ● Be sure to wear spark protection glass (es), long-sleeve shirts, gloves, etc. in order to

4 Caution: Burns ● Do not touch the engine and muffler during operation and immediately after stopping the equipment, for the temperature can reach e

5 Location of warning labels When any warning label becomes unreadable or damaged, place a new label on the appropriate location. When ord

6 Model DGW310DMC DGW310MC Generating Method Rotating Field Rated Current (A) 260 280 Rated Load Voltage

7 ● Arc Welding ● Electric Tools and Home Appliances ● Power Supply to lights DGW310DMC 3. Use 4. Parts Caution