Shindaiwa 89282 User Manual download pdf

Installation and Loading Instructions

Package Contents:

1 Speed-Feed

High Capacity LH Universal Mount Trimmer Head

Bushings

(F) 1 - 8mm x 1.25mm LH Bushing (3 notches)

(G) 1 - 10mm x 1.0mm LH Bushing (1 notch)

(E) 1 - 10mm x 1.25mm LH Bushing (No notches)

(J) 1 - 10mm x 1.25 LH Long Bushing (No notches)

(M) 1 - Reversible Nylon Spacer w/20/25/38 mm Recesses

Mounting Studs

(H) 1 – 7mm x 10mm Mounting Stud (Gold)

(I) 1 – 8mm x 10mm Mounting Stud (Silver)

Trimmer Head Installation

1. Insert locking tool (A) into gear case to lock output shaft (B). Remove existing cutting attachment (C) from unit

following manufacturer’s instructions.

IMPORTANT: Your unit must be equipped with a debris shield including a line cutter that will cut line to length

when trimmer line is advanced.

2. Install or reuse unit manufacturer’s gear case base plate (D). Base plate must support trimmer head and allow it

to rotate freely.

3. Select and Install Speed-Feed

Mounting Hardware

Use the Speed-Feed

Application Chart provided to identify the bushing or bushing and mounting stud

combination needed for your model.

IMPORTANT: For Echo units only. Check debris shield on unit for “R” mark between cutoff blade screws.

a. Units with “R” mark – Speed-Feed

line head will t on unit as is - go to Step 6.

b. Units without “R” mark – Remove short bushing from Speed-Feed

line head and replace with long

bushing (J) and use spacer (M).

NOTE: If your brand or model number is not listed, match the existing mounting hardware from your model

with Speed-Feed

mounting studs and/or bushings to determine the correct parts needed. If you need help,

visit www.speedfeedhead.com, or call the Consumer Product Support Department at 1-800-432-3246 from

8:30 am to 4:30 pm (Central Time) Monday through Friday.

NOTE: Bushing (E) (used with LH1, LH2, LH6) is preinstalled in trimmer head. Bushing (F) (used with LH3,

LH4), bushing (G) (used with LH5), and (J) (used with LH6) are included in the package. If required, depress

locking tabs (T), and open trimmer head (K) to install new bushing. Reassemble trimmer head in reverse

order of disassembly. Make sure “L” mark is facing up when replacing spool. Trimmer head halves will snap

together tightly only if parts are properly assembled.

4. If required, install new mounting stud (H) (7mm x 10mm) or (I) (8mm x 10mm) into threaded hole in gear case

output shaft (B). Turn “LH” studs counterclockwise to tighten.

5. If required, place reversible spacer (M) on base plate of gearcase, matching spacer recess to pilot diameter of

base plate.

NOTE: When spacer is properly matched and installed, there should be no gap between spacer and base

plate on gearcase.

6. Attach New Trimmer Head (K)

Thread trimmer head counterclockwise on to mounting stud or output shaft. Hand-tighten only.

NOTE: There should be no gap between spacer and line head after tightening.

IMPORTANT: Do not force, otherwise threads will strip and cause permanent damage. Unscrew and conrm

correct thread size.

7. Remove locking tool (A) from gear case.

8. If necessary, cut trimmer lines so length does not extend beyond the cut-off blade on debris shield.

9. To feed trimmer line, bump bottom of trimmer head against ground while running at normal operating speed.

E, F, G, or J

Speed-Feed

High Capacity Universal LH Trimmer Heads

P/N 78890-21001

X7672050801

01/11

H,I

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - Speed-Feed

BCInstallation and Loading InstructionsPackage Contents:1 Speed-Feed® High Capacity LH Universal Mount Trimmer HeadBushings (F) 1 - 8mm x 1.25mm LH

Page 2 - Réf. 78890-21001

2Instructions d’installation et de chargement Contenu :1 tête de coupe à montage Grande Capacitié universel Speed-Feed® LHManchons (F) 1 - Mancho

Page 3

3Packungsinhalt:1 Großraum-Fadenkopf Speed-Feed® LHAdapter (F) 1 - 8 mm x 1,25 mm LH Adapter (3 Markierungen) (G) 1- 10 mm x 1,0 mm LH Adapter (1 Ma

Page 4 - Codice ricambio 78890-21001

4 Istruzioni di montaggio e caricamentoContenuto della confezione:1 testina per bordatore Speed-Feed® Universal LH ad Alta CapacitàBoccole (F) 1 - b

Page 5 - N/P 78890-21001

5BCADIEE, F, G, or JTTMMJHGFDBKH,IAALInstrucciones de instalación y cargaContenido del paquete:1 cabeza de recortadora de montaje gran capacidad unive

Page 6

6Chargement de la ligne du taille-bordures1. Couper un morceau de ligne de la longueur préconisée.2. Aligner les èches de la partie supérieure du bou

Page 7 - Indicatori di usura

7NO. PART NUMBER DESCRIPTION NOM DE LA PIÈCEBESCHREIBUNG DESCRIZIONEDESCRIPCIÓN QTY.1 X473000031 SPOOL LH BOBINE LH FADENSPULE BOBINA LH CARRETE LH 12

Page 8

Speed-Feed®Trimmer Head Application ChartTabla De Aplicaciones De CabezalesTableau D’Application De La TeteLeft Hand Thread Trimmer UnitsUniversal Spe

Comments to this Manuals

No comments

Shindaiwa 89282 User Manual

Browse online or download User Manual for Grass trimmers Shindaiwa 89282. Speed-Feed® High Capacity Universal LH Trimmer Heads P/N

Summary of Contents

Comments to this Manuals

Related products and manuals for Grass trimmers Shindaiwa 89282