Shindaiwa AH2510 Operator's Manual download pdf (Page 8)

8

WARNING!

Never run the engine when adjusting

the cutter assembly to the storage

position.

Figure 17

Gearcase rotated to the

storage/transportation position

Adjusting the Cutter Assembly for

Storage or Transportation

Adjusting the Hedge Trimmer Cutter Assembly (continued)

WARNING!

Minimize the Risk of Fire!

n ALWAYS stop the engine and al-

low it to cool before refueling. Avoid

overlling and wipe off any fuel that

may have spilled.

n Wipe all spilled fuel and move the

engine at least 10 feet (3 meters)

from the fueling point and source

before restarting!

n NEVER start or operate this unit if

there is a fuel leak.

n NEVER start or operate this unit if

the carburetor, fuel lines, fuel tank

and/or fuel tank cap are damaged.

n NEVER smoke or light any res

near the engine or fuel source!

n NEVER place any ammable ma-

terial near the engine mufer!

n NEVER operate the engine without

the mufer and spark arrester in

good working condition.

IMPORTANT!

Mix only enough fuel for your immediate

needs! If fuel must be stored longer than

30 days and oil with fuel stabilizer

is not used, it should rst be treated with

a fuel stabilizer such as STA-BIL™.

Mixing Fuel

CAUTION!

This engine is designed to operate on

a 50:1 mixture consisting of unleaded

gasoline and ISO-L-EGD or JASO FC

class 2-cycle mixing oil only. Use of

non-approved mixing oils can lead to

excessive carbon deposits.

CAUTION!

n Some types of gasoline contain al-

cohol as an oxygenate. Oxygenated

gasoline may cause increased op-

erating temperatures. Under certain

conditions, alcohol-based gasoline

may also reduce the lubricating

qualities of some 2-cycle mixing oils.

n Never use any type of gasoline

containing more than 10% alcohol

by volume! Generic oils and some

outboard oils may not be intended

for use in high-performance 2-cycle

type engines, and should never be

used in your Shindaiwa engine.

n Use only fresh, clean unleaded gasoline

with a pump octane of 87 or higher.

n Mixed with 50:1 Shindaiwa ISO-L-EGD

or JASO FC class 2-cycle mixing oil at a

gasoline/ratio of 50:1 (1 gallon of gaso-

line to 2.6 ozs mixing oil). Shindaiwa

One meets or exceeds these require-

ments.

Oil is a registered JASO FC

classiﬁed oil and also meets or exceeds

ISO-L-EGD performance requirements.

Shindaiwa One is recommended for use

in all Shindaiwa low emissions engines.

Shindaiwa One also includes a fuel

stabilizer.

Examples of 50:1 mixing quantities

n 1 gallon of gasoline to 2.6 oz. mixing oil.

n 5 liters of gasoline to 100 ml. mixing oil.

Filling the Fuel Tank

1. With the engine off, install the scabbard

onto the blade.

2. Using the procedures described on the

previous page, rotate the cutter assem-

bly so it is parallel to the tube. Make

sure the latch lock and the latch release

return securely to a locking position.

See Figure 17.

3. Make sure the scabbard is in place on

the cutters before storing or transporting.

1. Place the unit on a ﬂat, level surface.

2. Clear any dirt or other debris from

around the fuel ﬁller cap.

3. Remove the fuel cap, and ﬁll the tank

with clean, fresh fuel.

4. Reinstall the fuel ﬁller cap and tighten

ﬁrmly.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 19 20

Comments to this Manuals

No comments