Shindaiwa EB802RT User Manual download pdf (Page 6)

6

Static Wire

Connector

Static Wire

Fold wire

Flexible Tube

Swivel

Tube

Anti-Static

Wire

Flexible Tube

89mm Clamp

102mm

Clamp

Figure 4

Swivel Tube

Swivel

Tube

Lock Pin

Lock Slot

Rotate clockwise to lock making

sure the 3 lines are aligned on

both tube and nozzle.

IMPORTANT!

Blower tube installation affects blower

performance! Make sure the tubes and

nozzle are correctly assembled per above,

and that all connections are tight. Blower

tubes may come apart during use unless

tubes are aligned and locked into place.

Align the lock pins with the lock

slots, and push the tube and

nozzle together.

Figure 6

Assembly

WARNING!

Danger from rotating

impeller!

Stop the engine before installing or

removing the blower tubes! Never

perform any maintenance or assem-

bly procedures on this unit while the

engine is running!

Figure 5

Handgrip

Short Nozzle

(ø65 mm)

Straight Tube

Long Nozzle

(ø74 mm)

90° Discharge Tube

Prior to Assembly

Using Figure 3 as a guide, familiarize your-

self with the blower and its components.

Understanding the unit helps ensure top

performance, longer service life, and safer

operation.

Before assembling the blower, make sure

you have all required components.

IMPORTANT!

The terms “left”, “left-hand”, “LH”; “right”,

“right-hand”, and “RH”; “front” and “rear”

refer to directions as viewed by the opera-

tor during normal operation.

Power unit and blower assembly.

Flexible tube, swivel tube, two nozzles

and straight tube.

Handgrip (Non RT unit only).

Two tube clamps (102 and 89mm).

This Owner’s/Operator’s Manual

and a tool kit containing a tool

bag, 4 mm hex wrench, 5 mm hex

wrench and a combination spark plug

wrench/screwdriver.

■

■

■

■

■

Lead wire assembly (anti-static).

Carefully inspect all components for damage.

■

Assembling the Blower

Place the blower upright on the ground

or a sturdy work surface and note parts

orientation as shown in Figure 4.

Remove static wire from package and

ﬁx eyelet to right hand engine cover

screw. See Figure 5.

Turn the discharge tube out to a right

angle and slip anti-static wire through

the 102mm clamp and ﬂexible tube.

Slip the ﬂexible tube over the end of the

90° discharge tube, and secure with the

102mm clamp.

1.

2.

3.

4.

IMPORTANT!

This unit is equipped with a static dis-

charge reduction wire. This wire helps

direct static buildup into the air stream

reducing the felt amount to the operator.

NOTE:

Check to make sure that the 90° discharge

tube swivels freely. If any binding is pres-

ent, loosen 102mm clamp and pull wire

towards engine to get more slack and

recheck for free movement.

Insert the static wire through the swivel

tube, then install and tighten the 89mm

clamp over the rotating band on the

swivel tube.

Slide the handgrip over the swivel tube

and secure with the bolt and wingnut.

Fold the end of the static wire back

over the connection of the swivel tube.

See Figure 5.

Grasp the nozzle, and push the nozzle

over the swivel tube locking pins secur-

ing the static wire. See Figure 6.

Lock the nozzle to the swivel tube by

rotating the nozzle noting the alignment

marks. See Figure 6.

5.

6.

7.

8.

9.

1 2 3 4 5 6 7 8 9 10 11 ... 59 60

Comments to this Manuals

No comments